If you limp into a gas station with a nearly flat tire, you will notice the tire gauge on the airline reads nearly zero when you begin to fill it. In fact, if there were a gaping hole in your tire, the gauge would read zero, even though atmospheric pressure exists in the tire. Why does the gauge read zero? There is no mystery here. Tire gauges are simply designed to read zero at atmospheric pressure and positive when pressure is greater than atmospheric.

Similarly, atmospheric pressure adds to blood pressure in every part of the circulatory system. (As noted in Chapter 11.5 Pascal’s Principle, the total pressure in a fluid is the sum of the pressures from different sources—here, the heart and the atmosphere.) But atmospheric pressure has no net effect on blood flow since it adds to the pressure coming out of the heart and going back into it, too. What is important is how much greater blood pressure is than atmospheric pressure. Blood pressure measurements, like tire pressures, are thus made relative to atmospheric pressure.

In brief, it is very common for pressure gauges to ignore atmospheric pressure—that is, to read zero at atmospheric pressure. We therefore define gauge pressure to be the pressure relative to atmospheric pressure. Gauge pressure is positive for pressures above atmospheric pressure, and negative for pressures below it.

In fact, atmospheric pressure does add to the pressure in any fluid not enclosed in a rigid container. This happens because of Pascal’s principle. The total pressure, or absolute pressure, is thus the sum of gauge pressure and atmospheric pressure: [latex]{P_{\text{abs}}=P_{\text{g}}+P_{\text{atm}}}[/latex] where [latex]{P_{\text{abs}}}[/latex] is absolute pressure, [latex]{P_{\text{g}}}[/latex] is gauge pressure, and [latex]{P_{\text{atm}}}[/latex] is atmospheric pressure. For example, if your tire gauge reads 34 psi (pounds per square inch), then the absolute pressure is 34 psi plus 14.7 psi ( [latex]{P_{\text{atm}}}[/latex] in psi), or 48.7 psi (equivalent to 336 kPa).

For reasons we will explore later, in most cases the absolute pressure in fluids cannot be negative. Fluids push rather than pull, so the smallest absolute pressure is zero. (A negative absolute pressure is a pull.) Thus the smallest possible gauge pressure is [latex]{P_{\text{g}}=-P_{\text{atm}}}[/latex] (this makes [latex]{P_{\text{abs}}}[/latex] zero). There is no theoretical limit to how large a gauge pressure can be.

There are a host of devices for measuring pressure, ranging from tire gauges to blood pressure cuffs. Pascal’s principle is of major importance in these devices. The undiminished transmission of pressure through a fluid allows precise remote sensing of pressures. Remote sensing is often more convenient than putting a measuring device into a system, such as a person’s artery.

Figure 1 shows one of the many types of mechanical pressure gauges in use today. In all mechanical pressure gauges, pressure results in a force that is converted (or transduced) into some type of readout.

An entire class of gauges uses the property that pressure due to the weight of a fluid is given by [latex]{P=h\rho{g}}.[/latex] Consider the U-shaped tube shown in Figure 2, for example. This simple tube is called a manometer. In Figure 2(a), both sides of the tube are open to the atmosphere. Atmospheric pressure therefore pushes down on each side equally so its effect cancels. If the fluid is deeper on one side, there is a greater pressure on the deeper side, and the fluid flows away from that side until the depths are equal.

Let us examine how a manometer is used to measure pressure. Suppose one side of the U-tube is connected to some source of pressure [latex]{P_{\text{abs}}}[/latex] such as the toy balloon in Figure 2(b) or the vacuum-packed peanut jar shown in Figure 2(c). Pressure is transmitted undiminished to the manometer, and the fluid levels are no longer equal. In Figure 2(b), [latex]{P_{\text{abs}}}[/latex] is greater than atmospheric pressure, whereas in Figure 2(c), [latex]{P_{\text{abs}}}[/latex] is less than atmospheric pressure. In both cases, [latex]{P_{\text{abs}}}[/latex] differs from atmospheric pressure by an amount [latex]{h\rho{g}},[/latex] where [latex]{\rho}[/latex] is the density of the fluid in the manometer. In Figure 2(b), [latex]{P_{\text{abs}}}[/latex] can support a column of fluid of height [latex]{h},[/latex] and so it must exert a pressure [latex]{h\rho{g}}[/latex] greater than atmospheric pressure (the gauge pressure [latex]{P_{\text{g}}}[/latex] is positive). In Figure 2(c), atmospheric pressure can support a column of fluid of height [latex]{h},[/latex] and so [latex]{P_{\text{abs}}}[/latex] is less than atmospheric pressure by an amount [latex]{h\rho{g}}[/latex] (the gauge pressure [latex]{P_{\text{g}}}[/latex] is negative). A manometer with one side open to the atmosphere is an ideal device for measuring gauge pressures. The gauge pressure is [latex]{P_{\text{g}}=h\rho{g}}[/latex] and is found by measuring [latex]{h}.[/latex]

Mercury manometers are often used to measure arterial blood pressure. An inflatable cuff is placed on the upper arm as shown in Figure 3. By squeezing the bulb, the person making the measurement exerts pressure, which is transmitted undiminished to both the main artery in the arm and the manometer. When this applied pressure exceeds blood pressure, blood flow below the cuff is cut off. The person making the measurement then slowly lowers the applied pressure and listens for blood flow to resume. Blood pressure pulsates because of the pumping action of the heart, reaching a maximum, called systolic pressure, and a minimum, called diastolic pressure, with each heartbeat. Systolic pressure is measured by noting the value of [latex]{h}[/latex] when blood flow first begins as cuff pressure is lowered. Diastolic pressure is measured by noting [latex]{h}[/latex] when blood flows without interruption. The typical blood pressure of a young adult raises the mercury to a height of 120 mm at systolic and 80 mm at diastolic. This is commonly quoted as 120 over 80, or 120/80. The first pressure is representative of the maximum output of the heart; the second is due to the elasticity of the arteries in maintaining the pressure between beats. The density of the mercury fluid in the manometer is 13.6 times greater than water, so the height of the fluid will be 1/13.6 of that in a water manometer. This reduced height can make measurements difficult, so mercury manometers are used to measure larger pressures, such as blood pressure. The density of mercury is such that [latex]{1.0\text{ mm Hg}=133\text{ Pa}}.[/latex]

A barometer is a device that measures atmospheric pressure. A mercury barometer is shown in Figure 4. This device measures atmospheric pressure, rather than gauge pressure, because there is a nearly pure vacuum above the mercury in the tube. The height of the mercury is such that [latex]{h\rho{g}=P_{\text{atm}}}.[/latex] When atmospheric pressure varies, the mercury rises or falls, giving important clues to weather forecasters. The barometer can also be used as an altimeter, since average atmospheric pressure varies with altitude. Mercury barometers and manometers are so common that units of mm Hg are often quoted for atmospheric pressure and blood pressures. Table 2 gives conversion factors for some of the more commonly used units of pressure.